Social Media


Sponsors

New 944Spec legal DMEs for $325 with promo code thanks to our newest sponsor, Focus 9 Tech!

Focus 9 Technologies

Official 944Spec Tees with a discount code for site wide Track Monkey discounts!

Track Monkey Apparel

Affordable Shifter Solutions and Other Parts from Only944!

Only944.com

10% Off Transmission Service and Parts from Flying Horse Motorsport!

Flying Horse Motorsport

Toyo Tires

Hawk Performance

EASY Porsche

Time Stilling Photography

Apex Performance

Paragon Products

comeau racing

Hanksville Hot Rods


Tarett

Race Render

AutoPoint Motors

Dart Auto
Welcome, Guest
Username Password: Remember me
Forgot your password? Forgot your username?
944-SPEC
Racing Discussion
Race Car Build

Re-wire Project Write Up
(1 viewing) (1) Guest
Reply Topic
New Topic

TOPIC: Re-wire Project Write Up

Re: Re-wire Project Write Up 13 years, 11 months ago #9333

Thanks guys. Yes, having the windshield out would be great but I don't need one and mine is put in the "regular" way. It would break if I tried to mess with it. Very good point though. The windsheild would probably be about the last thing I'd put in if were building a car.
Reply Quote

Re: Re-wire Project Write Up 13 years, 11 months ago #9334

Sterling Doc wrote:
Very cool - thanks for the post!

One tip I've used with good success is to dab a bit of clear silicon caulk on the on the spade connections. This is less of an issue with good connectors like you have, but helps vibration-proof connections. This tip comes from an ex BAJA off-road racer - battle tested. It ended my problems with the regular spade connectors.


Interesting, I've never heard that. Are you talking about putting on the end where wire casing meets the "plastic" part of the connector?

I try to not to use anything but the shrink fit connectors and on really critical parts (like the fuel pump), I use an additional piece of shrink wrap to reinforce it even more.

Thanks for the tip!
Reply Quote

Re: Re-wire Project Write Up 13 years, 11 months ago #9354

I revised the wiring diagram to show the installed condition and clean it up:
Reply Quote

Re: Re-wire Project Write Up 13 years, 11 months ago #9358

944Racer72 wrote:
Sterling Doc wrote:
Very cool - thanks for the post!

One tip I've used with good success is to dab a bit of clear silicon caulk on the on the spade connections. This is less of an issue with good connectors like you have, but helps vibration-proof connections. This tip comes from an ex BAJA off-road racer - battle tested. It ended my problems with the regular spade connectors.


Interesting, I've never heard that. Are you talking about putting on the end where wire casing meets the "plastic" part of the connector?

I try to not to use anything but the shrink fit connectors and on really critical parts (like the fuel pump), I use an additional piece of shrink wrap to reinforce it even more.

Thanks for the tip!


I put it over the top of the connectors, once plugged together, especially in areas that heat srhink is hard to use/get at. The silicon dampens vibrations, and holds things together.
Eric Kuhns

National Director Emeritus

2007, & 2008 National Champion
2011, 2012 2nd
Reply Quote

Re: Re-wire Project Write Up 13 years, 11 months ago #9461

  • RacerX
  • OFFLINE
  • Endurance Racer
  • Posts: 351
[quote="944Racer72" post=9325]
Here's the factory dash all stripped, cut in half, and painted. I added some aluminum C-chanel to hold the instruments and switches.



Nice. Did you keep the factory defrost like I did????
Ken Frey #3 944-Spec MW Region

"Racing is life! Anything that happens before or after is just waiting."

Check out my build thread!!
www.944-spec.org/944SPEC/forum/race-car-...d/9155-new-car-build
Reply Quote

Re: Re-wire Project Write Up 13 years, 11 months ago #9462

Nah, I'm a CA racer now and everyone knows it doesn't rain in CA

I've never really had a big problem with windows fogging. I've got a NACA duct on my passenger side window that I can point at the windshield when I want.
Reply Quote
Reply Topic
New Topic
944-SPEC
Racing Discussion
Race Car Build
Moderators: joepaluch, tcomeau, KLR
Banner
Powered by Kunena
Time to create page: 0.10 seconds